Circuit design
We review power, signals, and connections before defining the schematic.
At Nommada, we design custom electronic circuits and PCBs, paying attention to every detail so the electronics fit your product’s needs.
What happens today: You know what you want to solve, but not yet which circuit, sensors, or power supply you need. How we would approach it: We ground the use case and build a test for the most important technical question. What should change: You know what is worth building before investing in a final board.
What happens today: The test works with modules and wires, but takes too much space or cannot be repeated easily. How we would approach it: We design the circuit and PCB around the device’s size, cost, and actual use. What should change: You have a documented custom board ready for the next stage.
What happens today: The device resets, draws too much power, or fails only under certain conditions. How we would approach it: We reproduce the failure and measure power, signals, temperature, and components until we find the cause. What should change: You correct the failing point without discarding what already works.
What happens today: You need to read sensors, send commands, or store data, but the communication is not defined yet. How we would approach it: We choose interfaces and protocols based on distance, power use, environment, and data frequency. What should change: The device exchanges information on a clear technical foundation.






We review power, signals, and connections before defining the schematic.
We arrange components and traces for the available space and assembly. We can also start from a module based prototype.
We test the board in its intended setting and refine the design to better fit your product needs.
Yes. We define what the device must do and design the circuit and board around its power, signals, sensors, connections, and available space. We validate key decisions with an initial prototype.
Yes. We review what already works and what should be integrated into a custom board. To get started, send a short description and any photos, schematic, or prototype you have.
Yes. We reproduce the fault and measure power, current draw, temperature, signals, and communication. We use those findings to recommend a repair or redesign while retaining what works.
Depending on the scope, it can include the schematic, component selection, board layout and routing, manufacturing files, and prototype testing. We agree on deliverables before work begins.
Yes. We design electronics to read sensors, control actuators, and exchange data. Firmware, mobile app, or web platform integration is defined for each project.
It depends on circuit complexity, components, board size, and the testing required. Adapting a prototype also differs from designing from scratch. We define the scope before preparing a proposal.
Timing depends on requirements, component availability, and testing. Once the scope is clear, we plan the design, prototype, and validation stages with agreed timelines.
Yes. We are based in Ibarra and work with projects in other parts of Ecuador. Requirements, schematics, and designs can be reviewed remotely; when physical testing is needed, we coordinate how to carry it out.
Yes. We define what the device must do and design the circuit and board around its power, signals, sensors, connections, and available space. We validate key decisions with an initial prototype.
Yes. We review what already works and what should be integrated into a custom board. To get started, send a short description and any photos, schematic, or prototype you have.
Yes. We reproduce the fault and measure power, current draw, temperature, signals, and communication. We use those findings to recommend a repair or redesign while retaining what works.
Depending on the scope, it can include the schematic, component selection, board layout and routing, manufacturing files, and prototype testing. We agree on deliverables before work begins.
Yes. We design electronics to read sensors, control actuators, and exchange data. Firmware, mobile app, or web platform integration is defined for each project.
It depends on circuit complexity, components, board size, and the testing required. Adapting a prototype also differs from designing from scratch. We define the scope before preparing a proposal.
Timing depends on requirements, component availability, and testing. Once the scope is clear, we plan the design, prototype, and validation stages with agreed timelines.
Yes. We are based in Ibarra and work with projects in other parts of Ecuador. Requirements, schematics, and designs can be reviewed remotely; when physical testing is needed, we coordinate how to carry it out.
Ibarra, Esmeraldas y 13 de Abril 3304 y, 100201 Ibarra
Open · Closes at 10 p.m.
099 501 5706